WB DTM

Direct to Metal

Quote Calculator

Please fill in the information below in meters to calculate how much you need.

width

length

Here's what you need:

0 litres per coat
At a recommended 2 coat
You need a total of: 0 litres
Total Square Meters: 0 m²

Total Square Meters

litres per coat

Total litres you need

Name

Number

location

Features

Quick dry rust resistant water based primer, undercoat and topcoat.
Dries to a satin sheen finish Formulated with activated zinc phosphate as anti-corrosive additive for long term durability and stability.
Hard wearing and abrasive resistant.
Not recommended for high traffic and impact surfaces.

Where to Use

Stable mild and galvanized steel surfaces.

General Preparations

All surfaces must be clean, sound & dry.
Remove rust from mild steel substrates. If rust cannot be removed completely, spot prime with a rust converter before applying HydroEtch.
To improve adhesion, sand previously painted stable surfaces and apply Universal UnderCoat.

Technical Details

Product code:

Colour:

NDM201

White, Black and colours

Shelf Life:

Packaging:

Storage Conditions:

Stirring Method:

12 Months

1ℓ, 5ℓ, 20ℓ

Store in a cool/dry place

Stir with a flat paddle

Flashpoint:

Viscosity:

Specific weight:

Solids per volume:

Solids per mass:

Spreading rate:

Dry film thickness

Wet film thickness

Recommended coats:

Non-flammable

95 – 100 KU (at 23°C)

1.20 – 1.25

25 – 30 % (Approx.)

40 – 45% (Approx.)

10m2//1ℓ/coat

Depending on porosity, surface conditions and application equipment

25-30um (Recommended)

100um

Drying time:

Over coating:

Touch Dry: 15min@ 23°C

Dry to handle: IH@ 23°C

Minimum 2 hours@ 23°C

Maximum 1 days@ 23°C

Application:

Cleaning:

Brush, roller or Spray

Water

Precautions

Do not paint in moist/humid conditions.
For paint to cure, avoid exposure to water for at least 7 days.
Do not paint over surfaces with moisture content above 15% measured with an ultrasonic meter or over 5% with a pin type meter.
Stir paint well with a flat paddle.
Ideal application conditions and surface temperature should be between: 10°C – 35°C with a relative humidity of less than 75%.
It is not recommended to paint in direct sunlight as this will result in the paint drying too fast leading to visible “lap-marks”. Windy conditions might have a similar effect and can cause a deposit of dust particles on the wet paint.
To ensure colour– and sheen level consistency, purchase from the same production batch of paint. Touch-ups are not recommended.
Tint bases contain fewer litres than advertised until tinted.
Spreading rate is theoretical and based on a smooth and non-porous surface.
Do not wash or abrade newly painted surfaces until properly cured.
Allow 7 days for paint to dry properly and 30 days to reach full strength.
Store paint in a cool, dry place.
Complies with the South African legal lead limit of 90ppm or less.

Colour Selection

Colours tinted that fall outside of Laminin Largo’s formal tinting system may have risks regarding poor opacity, early fading, UV resistance, over and under tinting or alkaline attack. Please consult an official Laminin agent for advice.
Do not alter factory standard colours as this will compromise the products longevity i.e. fading, UV and alkaline resistance, colour consistency and opacity.
Bright colours plays an important role in colour selection, even though Laminin only makes use of lightfast pigments certain bright colours have a natural tendency for poorer opacity and UV resistance and might be more prone to alkaline attack. Please consult an official Laminin agent for the best possible advice.
Colour variations due to efflorescence (White salty deposits) (alkaline burn or attack) will not be covered under early fading or product failure.
The colour, white, may require a 3^rd topcoat to achieve opacity and full obliteration.

Health & Safety

Keep out of children’s reach.
Do not eat, drink or smoke during any application.
Ensure appropriate ventilation during application and drying.
Harmful if swallowed.
Wear protective equipment during preparation, application and cleaning.
Avoid contact with eyes.
In case of contact, seek medical advice.
Avoid contact with skin. In case of contact, clean with appropriate solvent.
If skin irritation occurs, seek medical advice.

Disclaimer

Specifications and recommendations are given in good faith and are meant to be used as guideline.
All information is based on results obtained from our tests done and experience gained over time
Application method and – equipment, condition of substrate and – during application, will have an influence on results. This is beyond the manufacturer’s control.
As technology may change over time, please ensure the use of the latest Technical Data Sheet