Rubon

Liquid Rubber

Quote Calculator

Please fill in the information below in meters to calculate how much you need.

width

length

Here's what you need:

0 litres per coat
At a recommended 1 coat
You need a total of: 0 litres
Total Square Meters: 0 m²

Total Square Meters

litres per coat

Total litres you need

Name

Number

location

Features

UV-, mould- and fungal resistant rubberised topcoat for walls, roofs and
parapets.
Waterproofing primer, undercoat and topcoat with excellent ponding
properties.
Airless spray application for excellent flow and levelling.
Dries to a high build smooth colourfast mid sheen finish to improve dust and dirt resistance.
Formulated with activated zinc phosphate and flash rust inhibitor as anticorrosive
additives for long-term durability and stability.
Prevents moisture ingress.
Ideal for exterior areas exposed to direct moisture and high humidity.
May be used with or without membrane.
A maintenance coat is recommended every 3 – 5 years depending on colour and
environmental conditions.
Please be advised that rubber in this context refer to a flexible and high build dry film
thickness.

Where to Use

Walls: suitably primed new and previously painted stable cement plaster,
concrete and porous brickwork.
Roofs: suitably primed new and previously painted stable galvanised,
tile and clay roofs.

General Preparations

All surfaces must be clean, sound & dry.
Remove all loose flakes and apply PlasterSeal or PlasterPrime to obtain a stable surface.
Smooth out plaster imperfections with Skim.
Repair plaster cracks with premixed Fill or tile cement / plaster mix & HydroKey, diluted 50% with water.
To stabilise chalky surfaces, apply PlasterSeal or PlasterPrime.
Previously painted sound surfaces can be washed with sugar soap and rinsed thoroughly with clean water.
To ease application, sand previously painted stable surfaces.
Sand and remove varnish to bare surface.
For water damaged, porous and alkaline surfaces, apply PlasterPrime or DampCure to stabilise surface.
Remove rust from mild steel and galvanized substrates. Apply HydroEtch or MSPrime to stabilise surface.
If rust cannot be removed completely, spot prime with a rust converter before applying HydroEtch or MSPrime.
Before recoating, sand previously varnished surfaces well to remove mirror-like image to a flat film.
Seal parapets in a criss cross pattern with fibre reinforced HydroFlex or WaterProof.
Waterproof roofs with membrane in conjunction with HydroSeal or EkoSeal.
Tile and clay roofs – apply one to two coats BondAll (Acrylic) until loose particles are thoroughly bonded.
Galvanized roofs – apply a single coat HydroEtch.

Technical Details

Product code:

Colour:

LRB00I

Colours

Shelf Life:

Packaging:

Storage Conditions:

Stirring Method:

12 Months

1ℓ, 5ℓ, 20ℓ

Store in a cool/dry place

Stir with a flat paddle

Flashpoint:

Viscosity:

Specific weight:

Solids per volume:

Solids per mass:

Spreading rate:

Dry film thickness

Wet film thickness

Recommended coats:

Non-flammable

106 – 112 KU (at 23°C)

1.25 – 1.30

40 – 45 % (Approx.)

52 – 56% (Approx.)

5 m2/1ℓ/coat

Depending on porosity, surface conditions and application equipment

100um (Recommended)

200um

1-3

Drying time:

Over coating:

Touch Dry: 2-4h @, 23°C

Minimum 6-8 hours@ 23°C

Application:

Cleaning:

Airless Spray .25 tip

Surface Temp 10 – 40°C

Ambient Temp 5 – 35°C

Relative Humidity 10 – 75 %

Water

Quality Guarantee

15 Years. A maintenance coat is recommended every 3 – 5 years depending on colour (dark colours like Charcoal and Black) and environmental conditions (i.e. UV exposure).

To VALIDATE quality guarantee, please register via our website or through your nearest distributor.

Terms and conditions apply – please consult the webpage for further information: www.laminincoatings.co.za.

Precautions

Avoid painting in moist/humid conditions. To allow applied paint to cure, there should be no rain forecast for at least 7 days.
Do not paint over surfaces with moisture content above 15% measured with an ultrasonic meter or over 5% with a pin type meter.
Stir paint well with a flat paddle.
Ideal application conditions and surface temperature should be between: 10°C – 35°C with a relative humidity of less than 75%. It is not
recommended to paint in direct sunlight as this will result in the paint drying too fast leading to visible “lap-marks”. Windy conditions might
have a similar effect and can cause a deposit of dust particles on the wet paint.
To ensure colour– and sheen level consistency, purchase from the same production batch of paint. Touch-ups are not recommended.
Tint bases contain fewer litres than advertised until tinted.
Spreading rates are theoretical and based on smooth / flat surfaces.
Do not wash or abrade newly painted surfaces until properly cured.
Allow 7 days for paint to dry properly and 30 days to reach full strength.
Store paint in a cool, dry place.
Complies with the South African legal lead limit of 90ppm or less.

Colour Selection

Colours tinted that fall outside of Laminin Largo’s formal tinting system may have risks regarding poor opacity, early fading, UV resistance, over and under tinting or alkaline attack. Please consult an official Laminin agent for advice.
Do not alter factory standard colours as this will compromise the products longevity i.e. fading, UV and alkaline resistance, colour consistency and opacity.
Bright colours plays an important role in colour selection, even though Laminin only makes use of lightfast pigments certain bright colours have a natural tendency for poorer opacity and UV resistance and might be more prone to alkaline attack. Please consult an official Laminin agent for the best possible advice.
Colour variations due to efflorescence (White salty deposits) (alkaline burn or attack) will not be covered under early fading or product failure.
The colour, white, may require a 3^rd topcoat to achieve opacity and full obliteration.

Health & Safety

Keep out of children’s reach.
Do not eat, drink or smoke during any application.
Ensure appropriate ventilation during application and drying.
Harmful if swallowed.
Wear protective equipment during preparation, application and cleaning.
Avoid contact with eyes.
In case of contact, seek medical advice.
Avoid contact with skin. In case of contact, clean with appropriate solvent.
If skin irritation occurs, seek medical advice.

Disclaimer

Specifications and recommendations are given in good faith and are meant to be used as guideline.
All information is based on results obtained from our tests done and experience gained over time
Application method and – equipment, condition of substrate and – during application, will have an influence on results. This is beyond the manufacturer’s control.
As technology may change over time, please ensure the use of the latest Technical Data Sheet